Drag to rotate · Scroll to zoom · True radial plane/contour intersections
DEMO GEOMETRY · NOT A PRINT PROFILE48° orbit · 22° elevation
Drag the reference curve handles to edit the shape; rib points are regenerated automatically at equal arc-length spacing.
1:1 physical scaling · 1 mm horizontally = 1 mm vertically
In steps 2 and 3, drag the green handles sideways or vertically, or click the green line to add a handle. Endpoints keep their Z positions. White rib points stay evenly spaced automatically.
The baseline is the exact per-height geometric midpoint of the two source profiles, with no smoothing across shared sections. The entire green curve remains editable. Physical XY-to-Z proportions are preserved at all times. Graph coordinates: radial distance from the model axis (horizontal) versus printed Z height (vertical). The dashed orange section is a smooth continuation of the shorter curve after it ends. Points are equally spaced by arc length along the geometric midpoint. The distance scale is normalized to the longest curve's length for comparison; the midpoint's shape is not distorted.
Horizontal Ribs / actual G-code passes
At each selected elevation, replace each normal wall with one larger bead. Center its path over the optimized wall directly beneath, then apply your offset and put its start/end on a confirmed hairpin intersection.
EXPERIMENTAL · REVIEW REQUIRED
Waiting for rib plan...
Nominal bead width. A 3.8 mm bead is extremely wide for the 0.8 mm nozzle; physical behavior needs calibration.
Requested speed; exporter lowers it where needed for the active profile's volumetric flow limit.
Changes M106 part-cooling fan only during rib extrusion; restores prior fan afterward.
All rib loops start/end precisely on a hairpin radial plane. On the three-branch upper section each closed contour automatically selects the nearest intersecting hairpin plane. Preview is top-down and approximately to physical XY scale.
Underlying wallNormal wall on this layerNew rib bead● Hairpin start/stop
Select a rib layer to see the new path.
The exporter replaces, rather than stacks, the selected wall loops. It preserves existing Z levels and the machine start/end code. Hairpin modifications are generated separately in Section 08. This is not validated physical bead geometry or a printability guarantee.
Hairpins / continuous inward U-turns
At each eligible plane intersection on a non-rib layer, generate an inward leg, U-turn, and return. Intersections that begin or end at genuine top/bottom boundaries can instead be protected for a selected number of layers.
EXPERIMENTAL · REVIEW REQUIRED
Waiting for geometry...
After a fixed 0.5 mm optimized-width shoulder and a 0.40 mm original-width jog, this slider determines the length of each 0.82 mm inward straight up to the U-turn. 0 mm disables hairpin detours. Paths stay on their hairpin planes.
Applies ONLY to the original-width inner hairpin legs and rounded turnaround. The first and last 0.5 mm optimized-width shoulders use the separate signed millimeter gap/overlap slider below. A symmetric jog joins the sections.
Signed bead-to-bead amount on the optimized-width 0.5 mm entry/exit shoulders only. −0.10 = gap; 0 = touching; +0.80 = overlap. The original-width inner legs keep their separate % overlap slider.
Suppress ONLY hairpin-plane intersections whose surface branch begins or ends at a true topology boundary (or the object's first/last layer). At the 1→3 split, continuing hairpins stay. Rib passes always take priority.
On each side of a plane-specific protected surface, taper ONLY the original-width inner straight over this many layers (default 4). The layer immediately next to suppression has zero inner straight: optimized-width shoulder → OG-width jog → rounded turnaround → return jog → shoulder. Continuing hairpins at the split remain full length. 0 = abrupt transition as before.
Used only on a loop with NO preserved hairpins. A tapered-extrusion overlap along the original contour; it does not alter layer height. Loops with any preserved hairpin keep the buried inward seam instead.
Preserved hairpin intersections take priority for burying loop start/stops. A tapered scarf-style overlap is used only if no hairpin remains on a loop. Horizontal ribs take priority over both. Rib layers stay unchanged.
Optimized wall before detourWall plus continuous U-turns● Turnaround tip
Select a non-rib layer to preview.
The exporter automatically slows only localized hairpin segments when short movements would exceed the conservative volumetric-flow budget; all bead dimensions and the wide-shoulder overlap are preserved. This version intentionally does not evaluate support beneath the inward legs, per your request. The entry and exit shoulders travel 0.5 mm inward with the regional optimized wall width and a user-adjustable signed bead gap/overlap (default +0.50 mm overlap). BOTH 0.40 mm transition jogs are extruded at the original sliced 0.82 mm width, followed by the inner straight length and rounded U-turn at the same 0.82 mm width with selected overlap. The two legs have adjustable nominal overlap; their midpoint and turnaround tip lie on the selected hairpin plane. The inward direction is chosen from which side of that plane lies within the current loop, not from a centroid. A U-turn adds extrusion and print time; physical adhesion, turning radius, cooling, collisions and the floating portions are unverified.
Support Propagation / permanent open arcs
Find unsupported spans using the original sliced wall contours only (not horizontal ribs or deliberately floating hairpins). Grow three permanent open supports from original-width hairpin legs. Each support keeps an identical narrow straight lead-in on both sides, then moves toward the unsupported profile while maintaining a bead-edge clearance from the exterior wall.
EXPERIMENTAL · REVIEW REQUIRED
Snaps to the first non-rib layer at or above the selected height. Supports grow until the detected unsupported layer.
If the selected hairpin is too short for a 0.4 mm exterior bead gap, only the three support-root hairpins get a minimum 2.5 mm inner straight. Other hairpins keep the slider length. This is reported in the JSON/audit; uncheck to require exact slider length (export may be blocked).
Overhanging support segments are capped at this speed. The surrounding path now accelerates and decelerates gradually.
Smoothstep speed ramp over this much printed path before and after every slow overhang segment. Affects nearby support and hairpin lead-in moves; 0 disables smoothing. This is a feedrate ramp, not automatic pressure advance.
Each island uses one distinct hairpin guide. Rib toolpaths remain unchanged; the support arcs now continue as separate narrow passes on rib layers.
Analyzing unsupported contours…
Original wallGrowing support arcFinal unsupported target● Hairpin roots
Select a layer to preview the support propagation.
Supports follow the original-width hairpin paths on regular layers, and are deposited as separate, original-width open passes across rib layers. They are permanent geometry, not removable slicer supports. Both support branches retain a matching narrow straight lead-in (calculated from the effective support-root length). The 0.4 mm minimum gap is measured between the support bead edge and the optimized exterior-wall bead edge at the SAME layer, including connecting segments. Near-wall portions of the growing support are displaced toward the interior; the target profile may therefore be approached less closely than in v1.15. A geometrical adjacent-layer XY comparison now slows support segments with more than 0.20 mm lateral shift. This is not a physical support or cooling simulation and does not guarantee printability. All horizontal rib toolpaths stay unchanged; the new support passes print after them on the two bridged elevations.
Attachment Fins / optional inward OG-width ribs
Choose a real top-surface boundary, imagine its matching part extending downward by the insert thickness, then build extra original-width hairpin fins ending at the underside of that imagined part. This is a reference body only; it is not printed. Select a surface to expose its intersecting hairpin directions.
EXPERIMENTAL · OFF BY DEFAULT
Fins terminate at top surface Z minus this depth. No extrusion is generated inside the imagined part.
Used for the inward diagonal fin below the insert underside in BOTH modes. Tip ends this many mm further inward. The fin tip grows along a straight 3D line from the lower root to its top, NOT a curved contour-following offset. Existing wall geometry, ribs, and support propagation are unchanged. Limited locally if the fin would pass through the opposing contour.
Defines the Z distance of the straight diagonal, from the first fin root to the insert underside.
Locating top surfaces…
Current wall outlineImagined part outline (reference)Enabled fin extension
Select a top surface to inspect its eligible hairpin intersections and the theoretical insert underside.
Each fin grows by lengthening ONLY the original-width section after the wide shoulder and transition jog. Optional vertical extension holds the last full-length hairpin's inner U-center fixed in XY down to just ABOVE the insert underside. The full diagonal 30mm fin still finishes at the underside, creating an inward-facing, flat fin seat; this forms a deliberate stepped side profile. Ordinary-layer fins are part of their hairpin's continuous extrusion path. On horizontal-rib layers, they print as separate original-width U-passes to maintain layer continuity, without changing rib geometry. Overlapping fins, collisions, the insert's precise solid volume, bridging, and mechanical fit are not physically verified. Some long reaches are clipped to avoid crossing another wall. Test before a full print.
Wall Optimization / regions between ribs
Measured geometry → user-controlled constant wall width and speed per region. Proposed centerline offset is a geometric preview only; no edited or printable G-code is produced.
PREVIEW ONLY · NOT PRINT VALIDATED
Smooths the measured layer-to-layer XY displacement across regions, then maps it into a configurable width range. Experimental geometry styling only; NOT a printability prediction.
Full-height width profileClick any section to inspect · solid = proposed width · dashed = relative XY shift (separate scale)
IDZ intervalMax shiftWidth
Select a region
Upload or load a single-wall G-code.
85%
Previous wallOriginal wallProposed wall
Changing rib positions redefines region boundaries, so drafts are only reused when their Z boundaries still match. The plotted bead envelopes use rounded/flat XY stroke geometry and an approximate inward contour normal. True slicer-quality offsets, outward-only overhang classification, inter-layer support, pressure dynamics, flow calibration and printable command generation are not yet implemented. Width/speed limits alone cannot establish printability.
Layer-by-layer planning
The sampled upward shift is a geometric diagnostic, not a verified printable-overhang limit. Multi-contour transitions require special review. Select a region to inspect it.
ZoneZ span (mm)Max XY shift∆XY / ∆Z
Select a region above.
Prototype conventions: rib elevations follow a user-editable geometric midpoint of the shortest and longest outer intersection profiles. A hairpin or seam direction is a fixed radial half-plane in model XY, extruded along Z; intersection points are calculated independently on every closed contour. Six evenly spaced radial directions correspond to three infinite vertical cutting planes. Each selected rib elevation produces one rib per closed loop. Rib start/stop anchors must be true intersections. Hairpin paths are available as experimental modified G-code, with an explicit audit. Experimental modified WALL G-code is available from section 06 and requires independent validation.